Jump to content

The Ebay Thread #2 - Post Ebay Parts Here!


XRQTR

Recommended Posts

HKS Surge tank 

** the new product was originally crystal-painted, but the paint has stopped after many years. It looks cool as it is, but I think it's okay to paint it with crystals to make it beautiful.
Nismo Solex is attached to the image, but the exhibition is only for the surge tank. Please be careful. **

May just be the tank? still cheap. 

https://page.auctions.yahoo.co.jp/jp/auction/n1004080359

Edited by Michael
Link to comment
Share on other sites

  • 1 month later...
  • Administrators

Big Job Lot on 2 rare / hard to find items for restorations.

Early S30Z ashtrays

https://www.ebay.com/itm/334177088780

5 good, 2 broken.

US $4,850.00

AM Radios

4 total

https://www.ebay.com/itm/334177117536

US $12,500.00

 

Link to comment
Share on other sites

  • 2 weeks later...
  • Administrators
  • 1 month later...

One needs to check the tip-to-tip dimensions against one's own Nissan original. I bought one several years ago as my original, which has already been re-chromed once, has rust breaking out in places. However, I found the new one was too tight across the bodywork at each end, so didn't proceed and it still hangs on the garage wall to this day. Nothing to say that my car is correct of course, that the guards shouldn't be pulled in a bit, although I think its original bumper fits pretty well. I must look at it again though, thanks for the reminder.

 

Link to comment
Share on other sites

  • 1 month later...

Well finally found time to again test fit the repro front bumper I bought a few yrs back. It came with holes for fitting the rubber strips and over-riders. I bought all new rubber strips at the same time.

Its tip to tip inside dimension is 1503mm, whereas my original is 10mm wider. On my initial test fit I had been concerned it was too tight and so had set it aside for another day. This time around, however, after applying lots of protective tape and very gently pushing the panels inwards just a little at the valance/sugar scoop bolt-up joint lines (on my car they tend to bulge there slightly) to gain a few precious mm, I found the new bumper slotted into place better than I'd expected. (It's still too close to the bodywork on the RH end, some more careful massage work is required there. LH end is fine now).

My original bumper has no doubt taken its share of knocks, and has already been re-chromed, so who knows how 'true' it is. Years ago the number plate and its brackets had been bent inwards, and my bending the brackets back into place - rather crudely - had stressed the metal and the chrome had crazed so that is why rust has developed. My bad. ::) 

But the new one is now on to stay! Am quite happy with the result. It wasn't a plug'n'play in my case, took time due to the vagaries of my particular car. I had to slot some of the holes for the fixing bolts of the rubber strips so they would comfortably fit without stress around the curves. (Maybe the rubber had shrunk while sitting in storage). I also slotted the holes for the over-riders so they could adjust to line up better.

The bumper came with an extra pair of holes top and bottom and inward of the over-riders, for bumper-mounted turn indicators I presume. Redundant in my case, I will source some chrome blanking plugs.

Before its final fit I also painted the back of the new one with a generous coating of silver cold galv to keep it good.

My 2c worth FWIW.

Link to comment
Share on other sites

  • Administrators

Set of Z Caps.

https://www.ebay.com/itm/363681064244

Price: US $2,000.00 buy it now.

You are bidding on a set of four Datsun Z hubcap.  Three (3) hubcaps are NOS, & one (1) hubcap is a very early take off.  Chrome is as new.  Center emblem is as new.  Paint shows minor scratches.  Very nice. Super rare find.  If you have any questions please call Kurt.

s-l1600.jpg

Link to comment
Share on other sites

  • 1 month later...
  • Administrators

Hang onto your Mikuni 44s folks..

https://bringatrailer.com/listing/complete-mikuni-44phh-triple-carb-setup/

20220124_134053-1-34372.jpg?fit=940,626

SOLD FOR $6,666 USD ON 2/14/22

Approx. $9,344.47 AUD.

Don't forget import duties such as GST and shipping on top!

Link to comment
Share on other sites

  • 2 months later...
  • 2 weeks later...
  • 1 month later...
  • Administrators

Set of D caps.

https://www.ebay.com/itm/275359322158

Starting bid:
US $1,800.00

s-l1600.jpg

Matching Topy's

https://www.ebay.com/itm/275359337822?hash=item401cb20d5e:g:AY4AAOSwF7RiqkX8

Starting bid: US $2,250.00

3 of the wheels are dated 3/71. 1 is dated 2/71

s-l1600.jpg

Link to comment
Share on other sites

  • Administrators

RE: D Cap prices, a few completed listings.

Single early cap (less fingers/tabs on back) for $536 USD

https://www.ebay.com/itm/225039901444

s-l1600.jpg

Another single early cap for $500 USD.

https://www.ebay.com/itm/295026991311

s-l500.jpg

And this set of D caps (NOS) was listed at $6,000 USD + no idea if they sold. (eBay says so)

https://www.ebay.com/itm/325140039226

s-l1600.jpg

Link to comment
Share on other sites

  • 5 months later...
  • 1 month later...
  • 4 months later...

A facebook member shared this the other day.

ARP Head studs from VPW (ebay Store) = $293.15 incl. shipping

ARP Cylinder Head Stud, Pro-Series, 12-point Head, For Nissan/ Datsun, L24, L26, L28 series, 6-Cyl, Kit

SKU: ARP-202-4206

(there's an eBay discount code you can apply to reduce the price from $318)

https://www.ebay.com.au/itm/325650427232

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...