Engine

889 topics in this forum

1. Oil filter mount

   By chris240, February 6, 2011
   • 4 replies
   • 1.8k views
   • 
   • Zedman240®
   • February 8, 2011

2. Engine size registration requirements for 260Z.

   By zeds4ever, January 31, 2011
   • 15 replies
   • 5.6k views
   • 
   • Wayne G
   • February 4, 2011

3. LD28 water pumps

   By Riceburner, January 16, 2011
   • 21 replies
   • 9.1k views
   • 
   • ozconnection
   • February 4, 2011

4. Rocker slipping 1 2 3 4 5

   By bullzed, December 28, 2010
   • 100 replies
   • 35.4k views
   • 
   • luvemfast
   • February 1, 2011

5. L28 Head gasket

   By Rhino73z, January 31, 2011
   • 4 replies
   • 4.7k views
   • 
   • Rhino73z
   • February 1, 2011

6. Air filter set up for LS1 / Holden 5Ltr EFI

   By wally57, December 24, 2009
   • 4 replies
   • 5.1k views
   • 
   • Cable
   • January 27, 2011

7. What Cam is this.

   By Gordo, January 21, 2011
   • 8 replies
   • 2.8k views
   • 
   • Zedman240®
   • January 22, 2011

8. 45DCOE Webers

   By 260Devil, October 19, 2010
   • 20 replies
   • 10.5k views
   • 
   • zedrally
   • January 20, 2011

9. 280zx hardtop possible install

   By tir33d, January 17, 2011
   • 1 reply
   • 1.7k views
   • 
   • Wayne G
   • January 17, 2011

10. Cleaning rebuilding Mikunis

    By d3c0y, January 11, 2011
    • 10 replies
    • 53.2k views
    • 
    • d3c0y
    • January 12, 2011

11. What hose where - L28

    By neRok, January 9, 2011
    • 8 replies
    • 11.2k views
    • 
    • neRok
    • January 11, 2011

12. 45mm Weber DCOE Ram Tube lengths

    By Whittie, December 23, 2010
    • 21 replies
    • 22.7k views
    • 
    • peter mc
    • January 10, 2011

13. Rear main seal leak.

    By Gordo, December 30, 2010
    • 10 replies
    • 6k views
    • 
    • peter mc
    • December 31, 2010

14. BMW Harmonic Balancer / Equivalent / Better

    By Whittie, September 26, 2010
    • 19 replies
    • 9.7k views
    • 
    • mossy
    • December 29, 2010

15. Cracked oil pump drive worm gear (crankshaft)

    By Whittie, December 23, 2010
    • 8 replies
    • 2.4k views
    • 
    • Whittie
    • December 29, 2010

16. New twin exhaust system!

    By Graedat, December 24, 2010
    • 2 replies
    • 1.4k views
    • 
    • Zedman240®
    • December 24, 2010

17. Rods/Bolts/Studs etc for a high compression motor

    By Whittie, December 23, 2010
    • 2 replies
    • 1.4k views
    • 
    • peter mc
    • December 23, 2010

18. R33 Wiper motor.

    By zeds4ever, December 18, 2010
    • 14 replies
    • 4k views
    • 
    • zeds4ever
    • December 21, 2010

19. Any tips for sump re-sealing? about to re-install turbo sump on L24e

    By DatPilot, August 17, 2010
    • 8 replies
    • 2.6k views
    • 
    • nat0_240_chevZ
    • December 21, 2010

20. Best bang for your buck L28 mods?

    By bullzed, November 10, 2010
    • 18 replies
    • 24.6k views
    • 
    • DatPilot
    • December 21, 2010

21. Exhaust Header design

    By GV260, May 21, 2010
    • 13 replies
    • 8k views
    • 
    • Six_Shooter
    • December 11, 2010

22. cost of 'non EGR' inlet manifold??

    By Retro Z, November 15, 2010
    • 3 replies
    • 1.3k views
    • 
    • Mr Camouflage
    • November 15, 2010

23. Cooling

    By Huw, November 12, 2010
    • 4 replies
    • 1.7k views
    • 
    • jamo240
    • November 12, 2010

24. L28 rods 1 2

    By Riceburner, October 27, 2010
    • 39 replies
    • 12.8k views
    • 
    • Scando
    • November 8, 2010

25. Cable Accelerator Conversion

    By Z, November 7, 2010
    • 7 replies
    • 6.5k views
    • 
    • garvice
    • November 8, 2010