juz0

Thanks to 24OUNZ ive purchased some round tops. Please close the thread

hello everyone. does anyone have some working round tops on a manifold with all the bits to just chuck straight on? I'm willing to pay for postage if outside of Melbourne Thanks Justin

yes mate it sure is running again. I haven't cleaned out the webers but it clears up after a few mins of running should be fine haha

thats all good, i'm back out to Moura for work this week and won't be back until the 9th of April. we can work something out The 260 is not for sale! it's so close to being on the road! just needs paint and a tune then good to go! UPDATE!!! also found some headlight buckets $20 a Pair of Bosch H4 headlights that have been modified to have a park bulb in the housing $40 for the pair

any offers on these last bits??

you'd have to get the bellhousing cut and shut. So cut off the original front part of the bellhousing and then welding on the front part of an L series bell housing. I was going to keep it and do this to mine but thats probably never going to happen haha. me and my big plans. you'd then need to fab up a gearbox mount and get a tailshaft made or use the end that comes with the gearbox, welded on to your current tailshaft. There is a thread on this site somewhere with lots of details on whats needed to get the bellhousing done. Just about any machining shop might be able to do it though? 6-speed manual 1st gear ratio 3.626 2nd gear ratio 2.200 3rd gear ratio 1.541 4th gear ratio 1.213 5th gear ratio 1.000 6th gear ratio 0.767

Also have front and rear suspension tubes ready to be cut up for coil over conversion $300 2x Factory rear LCA's $20 each

Hello everyone. It's been a long long time since i've posted on these forums! I'm doing a bit of a clean out before I move interstate in a few months so I've got some parts up for sale All located in South East Brisbane 2001 ADM s15 6 speed gearbox with around 88,000klm. didnt crunch any gears when removed from the car. it has the spline/flange from the tailshaft in the rear end ready for a conversion. Also has all the sensors and wiring plugs. $450 flat top carbies with manifold and all other bits $80 280zx efi set up, removed from running engine last year. includes ecm and wiring loom. $200 260Z boot, heavily rusted around the 4 corners of the glass seal. might be good for repairing? $20 55mm front and rear suspension tubes/knucles/hubs whatever they're called $250 260Z rear LCA's x2 $20 each RH tabco brand rocker panel replacement $120 sold pending payment RH tabco brand dog leg repair panel $60 sold pending payment single belt damper with 36 -1 tooth trigger wheel for aftermarket efi hall sensor $40 sold 260Z engine bay wiring loom, 90% complete, missing fuseable link box and some other bits $50 sold pending pick up Red polyurethane bump stop set and various sway bar bushes $20 sold pending payment 260Z vented bonnet, rust along front edge and around vents $100 sold pending pick up 260Z front LH fender, has rust in bottom corner and has been bogged up at the front from a previous accident but still looks fine and sugar scoop bolts on $50 sold pending pick up LH and RH sugar scoops $20 each sold pending pick up 260Z 2+2 front RH fender, has been cut up a bit for metal sections. FREE to anyone that can use it prefer pick up or can meet up in brisbane somewhere. I can post some stuff but the bigger stuff if you want posted will be done through pack n send regards Justin

Sure mate no worries.

Mossy if your feeling up to sending it up to brisbane, I'll buy just the hatch without the glass or the spoiler. Mine is really badly rusted out Gav can jump in on the spoiler if he still wants to buy it?

good job mate! looks very clean and the gauges suit the dash I reckon

i'm keen for the window frames but then I saw you have pick up only any chance you could drop them off at a pack and send shop??

you get really hung up on that d3c0y, just let it go buddy... let it goooooo

haha yeah! its so pimp!

Somebody has to buy this! http://www.boostcruising.com.au/advert/2300249-1972-Mercedesbenz-280s-for-Sale.html its a 1972 Mercedes with an L28! what do you guys think about it? I found it quite interesting