dpellizzaro

If you find the time to post I would like the arm rests. I'm in Brisbane, let me know if your willing. I'm not in a rush.

Set of 4 4x114.3 rota rb 17" rims with near new tyres. 2x 17x9.5 -19 offset with 255/40/17 nexen tyres (rears) 2x 17x9 -13 offset with 245/40/17 nexen tyres (fronts) Gunmetal centres with polished dish and lip. Wheels have only been test fitted and never driven on. I decided not to use these wheels and want to clear up room in my garage. Wheels located in Brisbane. Asking $1200 Email for photos.

Have pics of interior? Pm sent with email

Hi guys have a few items sitting in the garage I no longer need. Twin round top s.u carbs on manifold with e41 balance tube. Carbs will need service kit put through them as not sure last time they were used. Selling as is. $275 Ono. 260z air box in good condition. Painted ruby red. $175 Ono. MSA Rear Sway Bar 9/74-78 260Z-280Z, 7/8" brand new condition. $100 Front grill from 260z good condition $100neg. All items located in Carina, Brisbane 4152. Message for more details. Photos can be emailed.

Thanks guys, i think it might be to do with the set up Peter I purchased a pair of carbs which looked to be half decent but have struggled to get them to idle below 3000rpm. I did contact CNJ a while ago by email and didn't get a response. but those two are local so i will give them a go if all else fails. Cheers David

Hi guys, I have decided to get my round top S.U's professionally looked at, before pulling all my hair out. I was wondering if anyone has dealt with any good companies or would recommend someone who would be able to rebuild(if needed) and tune my HS4's. I just want it to drive well and use the car for weekend driving. I live on the south side and the car isn't registered, so i will need to tow and preferably would like to keep it as close as possible. But willing to travel. Thanks in advance David

I will have a look at those again, i know the springs are still fine and chokes appeared to be working. It would have to be something i am over looking. Thanks guys David

Hi guys, after fixing a lot of small problems with my 260z, I finally got it to idle over the weekend. It was a rough idle but not a bad place to start tuning. I let it idle for 5mins as it hasn't had a run for 6 months. After 5mins on idle there was a little backfire then the revs picked up to around 3-4000 rpm, I kind of freaked out and after blipping the throttle it didn't change anything. I left it to cool down and tried starting again but immediately the idle is quite high all idle screws are all the way out and I'm yet again scratching my head. Any ideas guys? Thanks David

Thanks for the replies. I have removed the plugs a few times and altho i haven't throughly inspected them, i hadn't notice the damage before. There were NGK plugs i cannot recall the product number but i purchased a full set of 6 just to replace them all and see what happens. I was thinking if i missed the damage and have swapped the plugs around then i might only need to look for 1 problem cylinder... How big would the debris need to be to cause the damage? are we talking a 8mm nut? How hard is it to remove the head? Thanks again

Hi guys, I have been slowly getting things back together on my 260z with L28 and swapped a set of flat tops for some round tops and after it was very roughly running(back firing and coughing a lot) for a few minutes i decided to look at the spark plugs and check if they were in good condition. i started checking from the back and when i removed the 3rd plug i noticed the firing end had been bent pretty badly and when found this to be the same on cyl 1 as well. Is there any thing i should be looking for other than some debris in a cylinder? i have a little inspection camera and i am going to look more into it, but i dont know what else would be doing it. Also is it possible if it is an item that has found its way into a cylinder, is that item able to move to another cylinder or would it most likely be trapped? thanks David

thanks guys, those photos are gold... i have been google image searching so many different things to get the right angles. I have all the emissions stuff stripped off mine and they seem to have been recently serviced and are in good clean condition. Hopefully they work well and i wont need to worry about round tops. either way im very happy with the response's and hope i dont need too much more help. cheers david

thanks message sent. i know that they have a bad rep, but i only have these to work with for the moment so i will try to make it work. Does anyone know where the vacuum line from the distributor connects to the carb? cheers david

hi guys just installed a pair of hitachi flat top su's from a 260z onto my l28. i was wondering where a couple of the vacuum hoses go and i have struggled to find any diagrams or any thing to point me in the right direction. Also is there a tuning guide for these carbs? Any help would be appreciated. cheers David

is there a better oil to use like a fork oil? and what weight would you reccomend for as it seems atf doesn't specify its weight. thanks david

I had big plans for the suspension on my 74 260z 2+2 but due to changes at work have had to put these plans off for a while, i have taken my front suspension appart and replace most the bushings and put in a 25mm front sway bar and was going to get new shocks and lowerd springs. How ever i am just going to put everything back together and enjoy it for a while. My question is if there is nothing wrong with the wet legs what do i have to do to reinstall them? is it just the case of refilling the shock tube with 380mL of atf and tightening up the gland nut on the top? or is there more involved? thanks david