Lots of 260Z and 280ZX stuff for sale

[RB30X]

Guys I have some gear I’ve collected that I need to move on due to project changes etc, and I have to pay back the missus 'some of my money she lent me' to buy this last car. Make offers for multiple items. For what it’s worth a lot of this stuff especially the aluminium parts look great after sand blasting (see *) so if you need a part or two and would like to buy it once sandblasted let me know. Sandblasting will incur a $30/hour fee.

 

2 x 280ZX inlet manifolds with or without efi gear including injectors and rail $50/each (bare) *

1 x separate injector rail $10

L28 dizzy (no cap) but including mounting base $100

3 x L28 exhaust manifolds $5/each

F54 block $50

L28 sump $25

N42 head (complete) $150

L28 rods and/or dished pistons

L28 timing cover *

L28 oil pump *

L28 thermostat housing with sensors $10 *

L28 90’ deg oil filter mount *

L28 idle pulley & adjust mechanism $10

2 x L28 starter motor $30/each

2 x L28 ignition coils $20/each

2 x 280ZX alternators $30/each

2 x 280ZX & 1 x 240Z clutch master cylinders (rebuild reccom) $10/each *

280ZX headlight surrounds $25

RB30E block $9.95

RB30E head (complete) $50

RB30 rocker cover $30

RB30 oil pump $20 *

240/260Z battery inspection covers $15/each

280ZX 25 spline stub axles $50

280ZX 25 spline companion flanges $20

280ZX 25 spline CV half shafts $50

260Z 2+2 fuel tank $40

280ZX fuel tank $40

260Z 2+2 rear control arms $50

260Z 2+2 55mm rear struts (complete) $70/pair

280ZX front struts $50/pair

280ZX rear struts $40/pair

280ZX rear control arms

260Z & 280ZX front rod and control arm thingys $10/pair

260Z dash vent thing $20

3 x 280ZX & 1 x 260Z radiators $40/each

Radiator shrouds

4 x L28 clutch fans $5/each

280ZX rear brake calipers $40/pair

R32 rear calipers and pads $100/pair

R31 rear calipers with brackets (unmodified) $100/pair

260Z door arm rests $30/pair

260Z 2+2 door cards $30/pair

260Z 2+2 inside cover for rear light panel

 

 

 

 

 

 

 

 

 

 

 

 

 

There's probably other stuff but that's all I could see on a shed tour today.

 

cheers

 

 

 

 

[chris240]

nope ...nothing for me      yet..

[RB30X]

please note, although there are coil over sleeves in  the pics of the R31 calipers, they are not for sale.

[Lgee]

shot gun the dizzy if it is electronic

 

[mlpinaus]

Sent a pm re the 260 lower controlarms and tension rods 

 

Marcus

[brianz]

The fuel tank in my 260Z 2+2 is full of rust, do you know the condition of the inside of your tank or has it been sitting unused for very long. That is what killed my tank. Also does one of the radiator shrouds fit a 2+2 and how much do you want. Any ideas of freight to the Gold Coast would also be appreciated.

 

Regards  Brian

[RB30X]

No it hasn't been sitting for very long and its been left so any moisture will drain out. I'll get a freight quote today.

[DatPilot]

L28 intake manifold, is it the webbed type or what? i have the webbed one and looking for a change

[RB30X]

Aren't they all webbed??

 

If they don't sell as is I was going to attack them with my porting tool.

 

 

 

 

[DatPilot]

you are quite a useful fella! auto valve bodies AND intake manifold porting! Im going to have to start up an account with you.

 

THere are about 6 or 7 intake fannymoulds that I know of, and some have no webbing, but have heaps of anit- pollution or something. I dont see any real gain in having it on there apart from protecting the injectors from the exhaust fannymould.

 

Im interested in a auto valve body still, and very possibly a sandblasted & ported intake manifold, matched to my KA24e Throttle body (65mm or something)

 

I will double check during the week, but I will have some invoices goin gthrough and scrounge up some cahs for ya. Let me know what you want

[RB30X]

Sounds good, you tell me the tbody diameter you want to match and the ball will roll. I thought from looking through Hybrid Z that those 'fannyfolds' without webbing were all custom chopped out by the owner?

[mlpinaus]

    Thanks for posting the lower control arms and the tension rods to me.  Thank you for doing exactly as you said

 

you would.  This is rare enough today, and you have fixed a real problem in rebuilding the wreck.  :'( Now on with the

 

quest for a good left fender/wing and a hood/bonnet. 

 

regards

 

Marcus

[RB30X]

No worries mate glad I could help out.

[DatPilot]

Cash ready.

1x L28 manifold with 31mm DIA opening for Throttle body.

PM sent regards to transmission gear too.

[Scoota G]

Gawd, (apologize to rev in advance) i so want to take another rb 30 rockercover and make another cold air intake.

[matto]

What bits you got left

 

 

[RB30X]

Heaps of stuff left mate. Just ask me what you need. 

[matto]

I'm rebuilding 280zx (1982) so anything in this line

 

Also looking at a 1981 model tomorrow in Melbourne that needs a new Starter - got these left ??

 

Thanks Matto

[japjag]

I am in desperate need for a 1 inch or15/16th brake master cylinder in good condition or better. Anything going?

[japjag]

Oops. To suit a 260 2+2

[RB30X]

I've got a few starter motors but no master cylinders.

[matto]

How much $ for both L28 starter motors - they both good??

 

I would need to have them freighted to Melbourne - what would that cost do you think??

 

Thanks