Jump to content
BenZed

Carbon and fibreglass parts from Restored (Japan)

Recommended Posts

I have a contact at Restored in Japan who can supply me some very hard-to-get fibreglass and carbon parts for Zs and other Datsuns. I can also get a big variety of parts for KPGC10 Skyline GT-Rs. If anyone is interested PM me.

 

The list below is the price excluding freight. Please PM me for freight estimates.

 

 

240Z (S30)

Carbon bonnet (carbon skin over fibreglass frame) $1250 

260Z fibreglass bonnet with vents $650

Full Carbon bonnet $1750

Fibreglass bumpers (front or rear same price) $325

Carbon bumpers (front or rear same price) $535

Fibreglass cowl panel (under wipers) $355

Carbon cowl panel (under wipers) $535

Fibreglass front guards $1200 pair

Carbon front guards (carbon outer skin, fibreglass frame) $2150 pair

Fibreglass flares (240ZG style) $260  IN STOCK

Carbon flares (240ZG style) $570

Carbon front spoiler with brake ducts $680

Fibreglass front spoiler with brake ducts $415  IN STOCK

Fibreglass headlight cowlings (pair) $580

Carbon rear spoiler $500

Carbon rear hatch (carbon skin over fibreglass frame) $1200

Full Carbon hatch $1750

Carbon tail light garnish $500

Fibreglass doors $2850 pair

Carbon doors (carbon outer skin, fibreglass inner shell) $3750 pair

Full carbon doors $4450  pair  ;D

 

280ZX (S130)

Carbon bonnet (carbon skin over fibreglass frame) $1200

Fibreglass front guards (pair) $1200

Fibreglass front spoiler $415

 

1600 (510)

Carbon bonnet (carbon skin over fibreglass frame) $1200

Fibreglass front guards (pair) $1200

Carbon bootlid (carbon skin over fibreglass frame) $890

Fibreglass cowl panel (under wipers) $355

Carbon cowl panel (under wipers) $535

 

1200 (GB122)

Carbon bonnet (carbon skin over fibreglass frame) $1200

 

240K (GC110)

Carbon bonnet (carbon skin over fibreglass frame) $1200

Fibreglass front guards (pair) $1200

Carbon bootlid (carbon skin over fibreglass frame) $890

"Racing Jacket" carbon headlight panel $390 IN STOCK

Fibreglass front apron $270

Fibreglass rear apron $270

Fibreglass chin spoiler $250

Fibreglass rear wing for 2-door $250

Fibreglass GT-R style flares $330

Fibreglass GT-R style grille $580

Carbon GT-R style flares $660

Fibreglass bumpers (front or rear) $300

Carbon bumpers (front or rear) $500

Carbon trims (around grille and tail light panel) $715

Fibreglass doors (for 2-door) $2850 pair

Carbon doors (carbon outer skin, fibreglass inner shell) $3750 pair

Full carbon doors $4450  pair  ;D

Parts for 4-door are available too, please PM me

 

Skyline RS (DR30)

Carbon bonnet (carbon skin over fibreglass frame) $1250

Carbon bootlid (carbon skin over fibreglass frame) $980

 

Fairlady (SR311)

Carbon bonnet (carbon skin over fibreglass frame) $1200

Carbon bootlid (carbon skin over fibreglass frame) $890

Full fibreglass door shells (pair) $2500

post-853-144023517266_thumb.jpg

post-853-14402351727_thumb.jpg

post-853-144023517273_thumb.jpg

post-853-144023517275_thumb.jpg

Share this post


Link to post
Share on other sites

without going to extreme (carbon fenders and doors, which i hope to see on your car ben!) my shopping list still totals 6g...one day!

Share this post


Link to post
Share on other sites

Some more parts added to the original post. Note the cowl panel and bumpers  ;D

Share this post


Link to post
Share on other sites

Sorry no pics available yet, but I imagine they're similar to the American ones on my car (see members projects)

Share this post


Link to post
Share on other sites

any pics on the carbon fibre 280zx bonnet???

post-853-14402352171_thumb.jpg

Share this post


Link to post
Share on other sites

Out of pure curiosity are these wet or dry carbon fibre?

 

They appear to be vacuum-bagged

Share this post


Link to post
Share on other sites

'Wet' carbon is just hand-laid into the mould like most fibreglass parts and the resin added with a brush and roller. This usually means the woven carbon cloth is not perfectly flat and even in the mould and you can have some air bubbles and excess resin.

Vacuum-bagging is a technique used to press the cloth flat and squeeze out the bubbles in the resin so you get a very smooth and even finish (plus a lighter final piece). As there is minimal resin the top surface also appears clearer (not cloudy), making the carbon look better too.

There are more steps to the process but this is the basic difference.

Share this post


Link to post
Share on other sites

"Wet carbon is layed up like fiberglass where dry cloth is layed on the surface and resin is then applied. It can also include vacuum bagging and autoclaving which improves strength. It could also be where the resin is drawn in from one end to the other by the vacuum in the vacuum bagging step. This is almost as good as pre-preg, and will be lighter and stronger than normal layup and resin application..

 

Dry carbon is prepreg, it's carbon cloth with presicely controlled amounts of resin applied already. You just lay it up, vacuum bag it and autoclave it. It's lighter and will be as strong as possible thanks to the exact right mix ratio of carbon and resin."

 

http://www.rx7club.com/showthread.php?t=587652

 

My mistake it's wet thanks.

Share this post


Link to post
Share on other sites

hey ben, can you get any 280zx airdams or any body kits?

 

I can get these parts from ARIX.

The front bumper is $700

Front spoiler is $400

Side skirts $450

Rear spoiler $150

post-853-144023528789_thumb.jpg

post-853-144023528794_thumb.jpg

post-853-144023528799_thumb.jpg

post-853-144023528804_thumb.jpg

Share this post


Link to post
Share on other sites

If you find 240ZG flares a bit narrow and ho-hum, these are the flares for you!

I have one set of these monster race flares which will fit over just about anything.

The photo shows what they look like fitted.

I brought these over in my last container to save freight, so you can have them for $550 plus local freight ($20-50 depending where you are). Can also be picked up at our new shop, 13 Bourke St North Parramatta.

post-853-144023538611_thumb.jpg

post-853-144023538619_thumb.jpg

post-853-144023562764_thumb.jpg

Share this post


Link to post
Share on other sites

One more bumper design, also $700

thats the one im after when can you get them in??? i was trying to buy it on auction in japan but the seller never replied. also the side skirts too :)

Share this post


Link to post
Share on other sites

thats the one im after when can you get them in??? i was trying to buy it on auction in japan but the seller never replied. also the side skirts too :)

OZ001 Instead of waiting for Ben to reply, Mate ring him....

email sales@otomoto.com.au

 

phone +61 2 8677 4890

fax +61 2 8677 4893

mail/workshop Otomoto Pty Ltd

13 Bourke St

North Parramatta NSW 2151

AUSTRALIA

 

 

Share this post


Link to post
Share on other sites

Ben are these the ones that go with the gnose or std nose?

 

Also could you give me the width of them

 

Thanks

Ash

 

If you find 240ZG flares a bit narrow and ho-hum, these are the flares for you!

I have one set of these monster race flares which will fit over just about anything.

The rears have notches to clear the rear bumper.

I brought these over in my last container to save freight, so you can have them for $550 plus local freight ($20-50 depending where you are). Can also be picked up at our new shop, 13 Bourke St North Parramatta.

 

Share this post


Link to post
Share on other sites

not sure but if you have a front spoiler I expect they will need to be modified to fit anyway.

The fronts measure just over 10cm at the top and the rears just over 14cm.

Share this post


Link to post
Share on other sites

hey ben, can you get rear bumpers for the 280zx??? if so can you add it to my my order of the front bar, side skirts, and rear wing.

 

cheers

Anh

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

×